240Z: Factory Transmissions knowledge, overview, Options and Specs

Ok guys, now it may get a bit techy in this post šŸ™‚ I collected A LOT of information about transmissions over the past few months and finally i put them all together into one single post. Much information is floating around the internet but it’s tricky to puzzle it all together, keep the overview and sort out the wrong information.
Picture below shows F4W71A Transmission, Picture from the 1970 FSM:

This post is focussing on the 1970-1974 240Z and will not include a lot of information about later transmissions or transmissions used in L20/S20 equipped JDM models, nor any other car with the same transmissions. Trust me, it’s complicated enough.
I tried my best to get the information right and have as much information as possible from original documents and manuals by Nissan but even the original documentation sometimes contradicts itself.

UPDATE 2020: I’ve added a lot of new information i’ve gained since the original post and ironed out a few details that were wrong and slightly reworked some sections.
Picture shows different JDM transmissions, scan from the Motorfan S30 special book:

1. Transmission type identification
1.1 Transmission type code
The transmission Model or type code is key to understand what transmission you have, and what is inside. They’re also mentioned in the Manuals and other documentation.
The Type-Code is NOT visible on the transmission anywhere!
I’ve already posted this in the past, but decided to make a better graphic for easy overview.
The chart does not include Automatic transmissions.
240Z factory transmission code key

1.2 Transmission Serial Numbers
Allthough the serial number hasn’t been any important yet in my cases, and it doesn’t lead you to any further information, i still wanted to share with you where to find the SerialNo. Stampos on the transmission housing.
Picture taken from the 1976 S30 Chassis & Body supplement 1 manual:

2. Factory transmissions:
2.1. Overview:

Depending on the country and year, there were different Factory Transmission options. But there are two main groups used in the 240Z:

Early “A-type”Ā  (1970 to late 1971, varying a bit depending on country and Type)
Later “B-Type” (1972 to 1974, also used in later Generation Z’s and other cars)

The “Type-Letter” is refering toĀ the lastĀ Letter in the transmission model code.
Early type for example is FS5C71A, later type FS5C71B, and so on, see code chart above.

Within each of these two main Groups, there are similar three subgroups:
Nissan 4-Speed Manual, Nissan 5-speed ManualĀ and JATCO 3-speed Auto.Ā 

IĀ made an overview Including the Type-code for easier understanding (click for full size):
Factory transmission overview
2.2. Transmissions according to Markets:
Which transmission was available in your market? Well – you can find this information in your FSM (Factory Service Manual) but here’s an overview:

USA & Canada (LHD): 4-speed Manual and 3-speed Auto*
Europe (LHD): 5-Speed Manual (, 3-speed auto, in some markets)
UK (Europe RHD): 5-Speed Manual (, 3-speed auto, in some markets)
Australia & Oceania (RHD): 5-Speed Manual, 3-speed Auto
Japan (RHD): 5-Speed Manual, 3-speed Auto (4-speed Manual only with L20)*
*Optional and competition transmissions are not included in this chart

Here is an Example of the 1972-1974 Service manual listing all B-type transmissions according to the dedicated market-model (first row).
For earlier model years, just replace all “B” with “A” in the transmission type code šŸ™‚
B-type transmissions

In The sales brochure of your country you’ll also find the Gearing / acceleration charts. Like the swiss sales brochure shown here:

3. Optional transmissions and Gearing
In Europe and Japan there were optional competition and racing Gearsets and complete gearboxes available for the Z’s. Here for E.g. JDM “Nissan Sports options”:


In USA however it was a bit different since they never got the 5-speed Manual Box:
– They offered Retrofit-Kits to install the Roadster 2000 (SR311) FS5C71A Transmission to the 240Z
– From 1977-1983 the 280Z FS5C71B Gearbox got available with optional competition Gearsets (and probably as a complete gearbox) which was also used as competition or racing part in the 240Z’s (with optional shifter-kit if used in an 1970-1971 car!)
– Anyhow a few sources mention that at least at some point the Euro / JDM A- and B-Box was also sold officially as an optional part, but i have no prove.
Here’s a Pic of the 1978 USA Datsun 240Z Sports Option catalogue for example:
option tranny parts usa
The Japanese sports transmission manual shows following gearing options including the Rallye Options listed for the FS5C71B type transmission used from 1972 upwards. According to the same book, the FS5C71A type transmission was used until end of 1971.

The early japanese Race & Rallye preparation manual shows following options available for the japanese S30 Variations also in comparison with other cars like the PGC10 skyline and SR311 Fairlady. There is a second (later) release of this manual, which probably also includes the B-type Manual transmissions, but which i don’t have.

See complete list of Factory and optional transmissions / gearsets a bit further down and also next chapter for racing gears.

4. Racing gears
I do not want to include a lot of information about racing cars. There were too many different setups used in the factory and private racing cars used over the years. but since i justĀ  happen to have this picture on hand i thought i’d share it here as well.
The 1970 RAC Rallye car gear setup (at least the speeds). by Autocar Magazine:

Here are the S20 engined Z432-R option gear sets from the september 1970 japanese sports option parts catalogue (including standard gears in the last row)

5. Automatic Transmission
The Automatic transmission is mostly common in American markets, in most other markets the manual transmission equipped cars are the primary sold units.
I found this interesting Text by “Road and Track” Magazine, when they reviewed the 240Z Automtatic car:

From the same 1970 Road and Track magazine, there’s this acceleration chart for the 3-speed Auto transmission:

5.1 A-type Automatic
It took me a while to figure out that the 3N71A unit was actually installed in the Z.

Most european part lists and Manuals only mention the B-type automatic.
However there is evidence that an A-type transmission existed and was installed.

And once i started to dig deeper, i found more information. See also chapter “Date of Changes”
I found this Picture of a 240Z A-type Auto transmissiom manual Online:

And it’s also listed in the 1979 Australian RHD FSM, even if you don’t find it in the Australian Parts-microfiches from the same year strangely.

For comparison. The european LHD FSM (picture taken from my own 1979 microfiche set) does not even mention the A-type Auto-transmission:

6. Differences between 5-speed A-, A- and B-type(s)
First a bit of history. The earlyĀ 5-Speed “A-Type” Transmission was not developed for the 240Z, but carried over from the Datsun roadster 2000 (SLR311) and probably also used in other older Datsun models.

To fit the L-series motor and the 240Z Specs, the 240Z-Transmission was fitted with a different clutch bell housing, longer mainshaft, tail Extension casing and one of the shift rods is different too.
That’s why the Roadster Gearbox is often refered to as “short tail” and the Z-Gearbox as “Long tail”Ā Fs5C71A Transmission.
The US market got 4-speed non-overdrive gearing,Ā but im not sure if there was an A-type 4-speed maybe used previously in other datsun’s as well..
Here’s a picture of a FS5C71A “short tail”Ā from a Datsun Roadster (From the Roadster FSM)
FS5C71A (roadster2000)

While here is a view of the FS5C71A “Long tail” from the Datsun 240Z (Picture from the Nissan Motorsports schematic Catalogue).


Also see the following pic, which is the FS5C71A Factory European Spec 5-speed that came with my two early 1972 240Z’s.
P1160981 - Kopie

Then there is the B-Type from the 1972+ 240Z which is a complete redesign of the “A-type” transmissions.
– The biggest difference is the two-piece Bellhousing of the A, while later B-type has a single piece bellhousing.
– Another visual difference are the Cast-fins on the outside of the housings as seen in the pictures above and here:
FS5C71B transmission

Here is a comparison between the A- and B-type from the S30 from the japanese G-works Fairlady Z S30 Magazine vol. 2:

– The A-type gotĀ the infamous so-calledĀ “Monkey Motion” rubber mounted shifter-stick while theĀ B-type shifters have a solid cross pin. Later Model C-types are retained in a top cover plate by a circlip (Called “Top Loader” in american trannies):

Here’s a closer look at my restored early A-Type “Monkey motion” Shifter before assembly:

– The gear ratios were different on both A- and B-types (both in 4- and 5-speeds)
– Due to the redesign the Shifter stick position is moved stlightly to the front in the “B-type” (See below).
– There were also other changes, so be careful when swapping transmissions!
– Note that the B-type Transmission was used over a Long time and in several cars after the 240Z, so it got various design-changes in later models which will or will not fit the 240Z. In this post i will not go into that topic!

Here’s a Comparison between the 240Z transmissions, Left to right:
FS5C71A “Long tail” 5speedĀ from the 1970-1971 240Z (non-US)
FS5C71B 5speedĀ from the 1972+ 240Z (non-US)
FS5W71C from Later Datsun / Nissan model cars
3N71B Spline Type 3-speed Automatic (1972+ non-Euro 240Z)

7. Date / Serialnumber of Change
When exactly did those Changes happen?

7.1 Automatic
The American Parts microfiche book states that the 3N71A Type transmission was used up to March 1971, before it was replaced with the 3N71B Type in April 1971:

According to the Japanese Parts microfiches, the A-type Auto transmission was used up to SNR S30-004902

And the first B-type Auto transmission started with Car No S30-004903

7.2 Manual 4-speed
The Japanese parts manual lists the Change from SNr S30-07500 for the Old F4W71A transmission, with the new F4W71B introduced at SNr. S30-07501

The American Manual says the A-type was used up to August 1971 and the B-type introduced from September 1971

7.3 Manual 5-speed

Strangely, the Japanese parts manual does not list a date or SNR for the change of the complete transmission assembly, like in the 4-speed manual or 3-speed auto transmissions. Inbstead they just list a date, until which the gear set from the FS5C71A was used. Namely up to SNr S30-8478 and PS30-514. I highly expect that this SNR is where the complete transmission changed from A-to by type.

Then there is the (pretty surely) wrong information stated in the Japanese sports transmission manual, t hat the B-type was only introduced in 1973:

And the Swiss 1979 Microfiche which doesn’t even name the B-type 5-speed, despite the facts that my two Swiss-spec Z’s both have them and many other’s i know. so this list is clearly incomplete too..

7.4 Center Console
There are two different types of Center consoles. One with the Ashtray in front of the stickĀ  and one behind. Some sources say that’s because of the difference in shifter stick Position in A- and B-transmissions (See above).

I made a picture for comparison:

I cannot confirm above information, since both of my early 1972 cars (built end of 1971) came with the early A-type 5-speed and the later Center console with the ashtray behind the stick (See picture below). This would be a wrong combination according to the sources but i’m pretty sure this was the factory equipment in both of my cars. It seems that the center console was changed indipendently from the transmission but around the same time, but not exactly. At least not in all markets (see information below)P1170175

The european, american and austrialian microfiches state that the console was changed from August 1971

The 1972 Parts manual from Japan just mentions the change in 1972, but also mentions the change introduced at SNr: S30-007501 and PS300501 (Z432). So probably export markets got the new console installed earlier?

8.1. Transmission interchangeability
8.1.1 Datsun Roadster 2000 FS5C71A into 240Z:
In America People used to install the Roadster 2000 FS5C71A transmission to get a 5-speed into their Z.Ā This Retrofit was officially sold by Nissan / NISMO USA.

I was able to find a receipt of someone who boughtĀ this swap at a nissan dealer including all the part numbers needed:
FS5C71A Conversion kit reciet1

The following information is from the 1998 american NISMO manual:

8.4.2 A-type with A-type
Swapping an ManualĀ A-type 4-speed to a 5-speed should be a simple thing without any modifications needed since both haveĀ similar length and shifter positions.

A 4 vs 4 speed

8.4.3 A-type to B-type
Here you can see a A-type US-spec 4-speed Transmission (front) and a B-type US-spec 4- or 5-speed in the rear. According to the source, both transmissions are within a small fraction of an Inch of each other in total length. The 510 Transmission identification Manual (See Documents below), Says that all 4- and 5-speed both A- and B-types of the 240Z have a total length of 31.5In / 775mm, so this might just be within the tolerances.

Trans Change Shifter dif Type A Type BTrany 001

You can see the Centerline of the “A”-Shifter in the foreground (line #3) sits about 2.25 inchehs behind the Center line of the B-type Transmission (rear, line #1).
Line #2 is the rear end of both transmissions.
Trans Change Shifter dif 001
To install a Later B-type five Speed, which was sold as Competition Part in US at one Point in a car that was initially equipped with an A-type (four Speed) Transmission, Nissan sold the “Shifter Kit” (Part number 99996-E3030) as seen on the B-type Transmission in the back. It’s basically a bent stick where the original one is straight. The Shifter kit is not available anymore (Courtesy Nissan Information to my request in 2016) but i guess you can just bend the original stick. Also a different propeller shaft is needed.
See also this information from the 1998 Transmission manual:

The shifter sticks are not interchangeable between A and B-type and 4- and 5-speeds.

8.4.4 Later Datsun / Nissan transmission swaps
There are possibilities to swap to a huge array of different Datsun / Nissan Transmissions, but to not make it more complicated for the Moment, i will make a separate post about this Topic later.

9. Transmission / gearing overview
I made an overview based on existing overviews and doublechecked everything with FSM’s, schematics, competition catalogues, E-Fast database, Original Micro-fiches and so on for hours. however sometimes some data was not 100% clear. anyhow i think this is the most complete overview about 240z Transmissions and (later) Options.

Note that this list is not 100% complete since there were also optional single gears to choose and 4-speed optional gears which i didn’t include in the list.
Also note that the part number for the same part may be different in different markets or may have changed over the time.
Transmission overview 240z
Click here to download the full PDF file (Free)

If text is coloured in a certain colour this means the “source” with the same text-colour mentioned this data, while all the other sources mentioned the black text. Sometimes it’s obviously a typographic ErrorĀ but in some cases im not sure.

Also note that there are several other Datsun / Nissan 71A/B Transmissions and Gear kits wich will fit the original transmission and / or L-Series motor but not listed above since they were used in different cars. The list above only contains transmissinos wich were used by factory or sold as option through nissan for the 240Z / Fairlady S30 in different markets.

10. Brass “Warner” vs Servo “Porsche” style steel Synchros
There are both Porsche style steel servo synchros and Warner style Brass synchros. What’s the difference? IĀ  have no own experiences but i found following information online:

– The porsche type reacts slower than the warner type
– Porsche type shifts smoother than Warner type
– Porsche type snycros dislike being “speed shifted” (probably due to lower reaction times)
– Warner type is great for drag racing (Fast shifting possible due to fast reaction times)
Since all “competition” transmissions came with porsche synchros despite having slower reaction times, i guess they can handle slightly more power and / or last longer under heavy usage compared to brass synchros. Otherwise it would not make a lot of sense to have these in “competition” (or non-US standard) gearboxes.

11. Clutch throw out bearing collars / sleeves
Upon request i added this information. I found it here:


A lot of people refer to the collar by the transmission, but that can be misleading. Its better to go by the year. Datsun changed the pressure plate the same time they changed the 71A to the 71B transmission. After that its all over the place. You can get a 71B 4 speed with thre different collars, just depends if its in a 240Z, 280Z or a 2+2.

The to drawing below show how you can get confused by using the transmission to determine collar height. The second drawing show the same, but per model Zed.

12. Speedometer Pinion Gear
Update 19.04.2017: I was looking myself for the correct speedometer pinion gear and figured out this part was missing yet. So here we go. I made a nice overview for you:

Picture from Zparts.com showing all the gears:

13. Transmission crossmembers
Update 02.02.2018: I Discovered there are totally three types of transmission crossmembers for the 240Z. Thought this might be useful to know as well, so check out the details in a separate post i made here with additional informations about the bushings: http://www.jdmjunkies.ch/wordpress/2018-02-04/240z-new-custom-made-transmission-crossmember-bushings/

14. Shift patterns
I found this picture in the Nissan Sports transmission manual, showing various shift patterns. Not all of these were used in the S30 chassis, but might still be useful in some cases:

15. Fluids
Coming soon

16. Optional / Competition / NISMO / Racing Parts
In the 1998 NISMO Catalogue i found a set of Aluminum bushings for the A-type Transmission:

And they offered also a set of stiffer Polyurethane Bushings for the B-type Transmission mount:

17. Original Documentation
There are a big range of original Service manuals and some not so obvious manuals available in various market versions for the different transmissions. Aside from the standard FSM and Parts manuals of course, which should always be the starting point.

Here you get a short overview and some are available as download:

Datsun FS5C71A transmission service manual (From Roadster 2000 SR311 Manual, will also works for 240Z 5-speed except a few design changes):
FS5C71A transmission service manual (Roadster 2000)

Nissan Motorsports schematic catalog (99996-M8015), which includes an english
FS5C71A / F5C71B Parts exploded view / Partslist:

Read more about it and download it here:

Datsun / Jatco 3N71A Automatic transmission Manual:
Datsun – Service Manual – Full Automatic Transmission – 3N71A

Nissan Japan Sports transmission Manual 1973

See full story and download here: https://www.jdmjunkies.ch/wordpress/2018-10-23/240z-nissan-sports-and-rallye-transmission-manual/

Japanese race and rally preparation Manual (picture shows early version):

“Five and dime” 510 Magazine Volume 11, Issue 4, Datsun / Nissan Transmission identification guide (See Pages 04-09 for a lot ofinformation):
Five and Dime vol11 issue 04 (Nissan Transmission Identification)

Datsun FS5C71A transmission Rebuild Manual by Rising Sun Racing (1987):
FS5C71A Rebuild Manual by Rising Sun Racing (1987)

18. Spareparts
Spareparts – especially for the early manual 5-speed are hard to find these dase, but below you find some adresses that still sell some parts:

Those japanese Vintage skyline and S30 specialists are definitely worth a visit.
here’s a flyer from Transmission specialist Vintagecraft-e-za, as an example:

Some parts like new bushings for the early A-type five speed transmission i found on ebay:

19. Useful Links
An overview about different nissan / Datsun transmissions and gearing:

20. Thanks for reading
I thank anyone who provided some information for this Post.
If you find any mistakes and can prove it with an official document, please let me know so i can update this post with the correct Information!

This entry was posted in 240Z Knowledge posts, 240Z Project. Bookmark the permalink.

25 Responses to 240Z: Factory Transmissions knowledge, overview, Options and Specs

  1. Bill Morgan says:

    As a point of interest, my 1970 240Z had a B-type 4-speed swapped into it at some point. It came with the original A-type 4-speed as well. In order to install the B-type trans without cutting the tunnel the installer used an MSA Short Shift kit, which comes with a bent shift lever. It isn’t helping me with the 5-speed trans I’m installing now, but gives me a pattern for bending the 5-speed lever.

  2. Nice work, Nils, thanks.

    I am a longtime employee at Toyota Motor USA and Lexus USA, but an even longer-time collector & restorer of a 1969 Datsun 510 racecar.

  3. Pingback: Help identifying a transmission? - Nissan : Datsun ZCar forum :Nissan Z Forum: 240Z to 370Z

  4. Loki says:

    Great write up! Do you happen to know about the throw out bearing collar size between type A 4sp vs 5sp? Reason is exedy performance clutch stage 1 stated it will work with 280z and not 240z/260z.

  5. Really great post! Thanks a bunch. From what I was told when I acquired a recent Datsun project it came with either a spares performance american Mod or an imported B model 5 speed for 240z. It seems to be a little rare. I was planning on putting it on ebay because my project does not require it. If you know anyone interested I have it in my workshop in West Virginia

    • Thanks for your Kind words and you’re very welcome. The post is a “under Progress” type of post. Meanwhile i found some additional Information, which i want to update.
      Regarding your question: In europe it’s not rare at all, but in america it’s one of the rarer transmissions for the Z, from what i understand. because it was never officially sold with a 5-speed.

      A good alternative to ebay is the “datsun parts and Needs” Facebook-Group. While there are a lot of idiots there tryping to lowball or trying to tell you your stuff is shit. There might be one or another Person interested in it. Otherwise i don’t know anybody interested, since we can find that Transmission quite easy over here in comparison.

      good luck with the sales. Cheers
      – Nils

  6. Robert Remkes says:

    Hi,I am swapping a 1970 4 speed to an a series 5 speed.The gearbox seems to have a flange at the output shaft on the 5 speed and a normal spline on the 4 speed for the front driveshaft yoke.

  7. Mike Williams says:

    Great information…thanks for all the hard work compiling the data.
    Would you happen to know how many automatics were produced in the 1971 Z? I have searched the internet to no avail. Thanks again. Great effort.

    • Hi, you’re very welcome. Will update this post soon, as it has a few wrong information. Anyhow I don’t know how many automatic were produced in the 71 Z i’m sorry. there is data how many were produced, exported, etc. but i don’t have any information about how many were automatic, i’m afraid. In general it’s hard to obtain these numbers, and when you get them they’re still vague…
      It also depents where you live. In europe only 5-speed manuals where sold, whereas in USA both 4-speed manual and three speed Auto were available and in Japan there were more options depending on which version of the car you got…

  8. John Sleesman says:

    Very thorough document. Thanks for all your work on this.

  9. Jerry M Hanchett says:

    I recently installed a close ratio five speed in my 72 240Z everything works great except the speed gear does rotate. I installed the four speed speed gear housing in the 5 speed. If I line up the housing with the tab/bolt retainer the speed gear doesn’t turn when rotating drive shaft. If a remove the retaining tab and rotate the gear housing it will engage but then the slot does not line up to install the retaining tab, it’s about 180 degrees off. Was there special speed gear housing for the close ratio trans?

    • Hi Jeremy. Good question. What type of transmission do you exactly have and which one was the original transmission? I could look into the documentatino and see if i can find something.

  10. Jerry M Hanchett says:

    removed original 4 speed from ’72 240Z, replaced with 78 280Z close ratio 5 speed, I bought already removed so I was told that is what it came out of, did not come with speedo gear.

    I used speedo gear from 4 speed but later got a gear from 5 speed.

    • Ah i See. When it’s about the later type cars I’m not 100% sure what transmission it is. I spent most of my time with 240Z cars and actually i dont really know what the 280Z came with, without doing some research. My manuals only cover the 240Z / 260Z and japanese fairlady. but i’m sure you find the parts manual online (carpartsmanual.com?) and can compare the partnumbers. in the original parts manual you should also see the exact type code of the transmissions you got. I’m sorry i can’t help you more, but i’m soure you find the information if you look around.

Leave a Reply

Your email address will not be published. Required fields are marked *